Interior Animations

For movement of various things in truck interior are used program driven animations ( _anim ). For each animation can be set range by *_anim_min and *_anim_max values. As most animations expect range from 0 to 1, this are also default values. If animation expect any other value range it will be stated below.

Special animations=

wheel_anim
wiper_anim
gadget_anim

Stick animations

blinker_anim
lights_anim
high_beam_anim
light_horn_stick_anim
wiper_stick_anim
parking_stick_anim
flasher_4way_anim
engine_start_anim - 0 off, 0.33 electricity on, 0.67 engine on, 1 engine starting
beacon_anim
trailer_stick_anim - trailer brake
retarder_stick_anim
auto_transmission_stick_anim - in order reverse-neutral-drive
lift_axle_stick_anim

Gauge animations

oil_psi_anim - range in psi (pounds per square inch), 40-90 psi is typical working value
water_temp_anim - in celsius degrees, working value 90*C
battery_anim - in volts, working value 24V
oil_temp_anim - engine oil temperature, in celsius degrees, working value 90*C
diff_temp_anim - differential temperature, in celsius degrees, working value 90*C
tachometer_anim - in rpm (revolution per minute)
speedometer_anim - speed in km/h
air_psi_anim - range in psi (pounds per square inch), working value 140 psi
brake_psi_anim - range is 0 to 1, maximum pressure value should be equivalent of 60-70 psi
suspension_load_anim - expects range in newtons (22t trailer creates like 70kN on kingpin)
fuel_anim
ad_blue_anim
turbo_anim
consumption_anim - instant consumption in l/100km, scania gauge has 0 to 120
clock_big_anim - minutes, 0-60
clock_small_anim - hours, 0-12
generic_anim - animation for other gauges. 0 when truck is turned off, 1 when truck is turned on.

Indicator animations

This animations are not interpolated from 0 to 1 rather they have only 2 states: switched off and switched on. So this animations should have only 2 key frames.

button_left_blinker
button_right_blinker
blinker_delay - this is not animation, but value describing length of half blinking loop
button_water_temp
indicator_oil_temp
indicator_position_lights
button_lights
button_high_beam_lights
indicator_aux_lights_front
indicator_aux_lights_roof
indicator_aux_lights_any
button_low_air_psi
button_low_oil_psi
button_battery_warning
button_low_fuel
indicator_low_adblue
button_jakebrake
button_parking_brake
button_4way - indicator should be placed on hazard warning button for blinking
indicator_retarder
indicator_warning - damage warning indicator
indicator_stop - critical damage indicator
indicator_axle_lift - lifted axle indicator
indicator_cruise_control
indicator_generic - animation for other indicator. 0 most of the time, 1 when truck is making electricity check (after turned on).

Dashboards IDs

Screen of dashboard computers uses our UI library and shows thus UI elements. Each element has unique ID and can be used only once (due to caching). Most of fields can be used as two parameter template - value and unit, both are used accordingly to current game options. As in different languages can be units and other texts translated ensure that there are enough space for all of them.

Screen IDs ( ui::group type):

100 to 800 - basic screens, up to 8 screens
900 - warning screen, used when truck is damage and should be repaired, shown alone (without shared screen)
950 - shared screen (used together with all basic screens)

Element IDs (mostly ui::text_common type):

1000 - ambient temperature
1010 - oil temperature
1020 - current speed
1030 - odometer, needs space for at least six digits
1040 - current gear, uses N, D[number], R or R[number] for automatic and N, [number], R or R[number] for maual
1050 - current clock time in proper format, eg. "12:34 pm"
1060 - remaining fuel in tank
1070 - ui::text for fuel bar, the text is cut left-to-right according to current fuel tank state
1075 - ui::text that defines size, orientation and range of fuel bar
1080 - guessed operating range of vehicle
1090 - water temperature
1100 - cruise control speed value
1110 - ui::text for oil pressure bar, the text is cut according to current oil pressure
1115 - ui::text that defines size, orientation and range of oil pressure bar (typical data "H~~0~~116", horizontal range 0psi to 116psi (8bar))
1120 - ui::text for air pressure bar, the text is cut according to current air pressure
1125 - ui::text that defines size, orientation and range of air pressure bar (typical data "H~~0~~174", horizontal range 0psi to 174psi (12bar))
1130 - ui::text for turbo pressure bar, the text is cut according to current oil pressure
1135 - ui::text that defines size, orientation and range of turbo pressure bar (typical data "H~~0~~1", horizontal range 0 to 1)
1140 - ui::text for adblue bar, the text is cut according to current adblue tank state
1145 - ui::text that defines size, orientation and range of adblue bar
1150 - ui::text for water temperature bar, the text is cut according to current water temperature
1155 - ui::text that defines size, orientation and range of water temperature bar (typical data "H~~0~~130", horizontal range 0*C to 130*C)
1160 - instant consumption
1170 - average (trip) consumption
1180 - unused
1185 - unused
1190 - damage warning icon, can be ui::group or ui::text or any other element that could show/hide
1200 - low fuel warning icon, can be ui::group or ui::text or any other element that could show/hide
1210 - trip distance
1220 - compass, displays strings like "N", "E", "SW".
1230 - engine brake icon
1240 - cruise control icon, can be ui::group or ui::text or any other element that could show/hide. Cruise control speed ( 1100) explicitly CAN be child of this group.
1250 - cruise control memory icon, can be ui::group or ui::text or any other element that could show/hide.

Data for bars are entered in format "H~~0~~130", H means the bar is horizontal (or V for vertical), leftmost position represents value 0, rightmost position represents value 130. Empty text defaults to "H~~0~~1".

Documentation/Engine/Truck Interior Animations and IDs

Contents